The influence of initial atomized droplet size on residual particle size from pressurized metered dose inhalers

Poonam Sheth, Stephen W. Stein, Paul B Myrdal

Research output: Contribution to journalArticle

15 Citations (Scopus)

Abstract

Pressurized metered dose inhalers (pMDIs) are widely used for the treatment of diseases of the lung, including asthma and chronic obstructive pulmonary disease. The mass median aerodynamic diameter of the residual particles (MMADR) delivered from a pMDI plays a key role in determining the amount and location of drug deposition in the lung and thereby the efficacy of the inhaler. The mass median diameter of the initial droplets (MMDI), upon atomization of a formulation, is a significant factor influencing the final particle size. The purpose of this study was to evaluate the extent that MMDI and initial droplet geometric standard deviation (GSD) influence the residual aerodynamic particle size distribution (APSDR) of solution and suspension formulations. From 48 solution pMDI configurations with varying ethanol concentrations, valve sizes and actuator orifice diameters, it was experimentally found that the effective MMDI ranged from 7.8 to 13.3 μm. Subsequently, computational methods were utilized to determine the influence of MMDI on MMADR, by modulating the MMDI for solution and suspension pMDIs. For solution HFA-134a formulations of 0.5% drug in 10% ethanol, varying the MMDI from 7.5 to 13.5 μm increased the MMADR from 1.4 to 2.5 μm. For a suspension formulation with a representative particle size distribution of micronized drug (MMAD = 2.5 μm, GSD = 1.8), the same increase in MMDI resulted in an increase in the MMADR from 2.7 to only 3.3 μm. Hence, the same increase in MMDI resulted in a 79% increase in MMADR for the solution formulation compared to only a 22% increase for the suspension formulation. Similar trends were obtained for a range of drug concentrations and input micronized drug sizes. Thus, APSDR is more sensitive to changes in MMDI for solution formulations than suspension formulations; however, there are situations in which hypothetically small micronized drug in suspension (e.g. 500 nm MMAD) could resemble trends observed for solution formulations. Furthermore, the relationship between APSDR and drug concentration and MMDI is predictable for solution pMDIs, but this is not as straightforward for suspension formulations. In addition, the MMAD R was relatively insensitive to changes in initial droplet GSD (from 1.6 to 2.0) and the solution and suspension pMDI residual particle GSDs were essentially identical to the initial droplet GSDs.

Original languageEnglish (US)
Pages (from-to)57-65
Number of pages9
JournalInternational Journal of Pharmaceutics
Volume455
Issue number1-2
DOIs
StatePublished - 2013

Fingerprint

Metered Dose Inhalers
Particle Size
Suspensions
Pharmaceutical Preparations
HFA 134a
Ethanol
Drug Compounding
Nebulizers and Vaporizers
Chronic Obstructive Pulmonary Disease
Lung Diseases
Asthma
Lung

Keywords

  • Aerodynamic particle size
  • Atomized droplets
  • Initial droplet diameter
  • Pressurized metered dose inhaler (pMDI)
  • Solution formulation
  • Suspension formulation

ASJC Scopus subject areas

  • Pharmaceutical Science

Cite this

The influence of initial atomized droplet size on residual particle size from pressurized metered dose inhalers. / Sheth, Poonam; Stein, Stephen W.; Myrdal, Paul B.

In: International Journal of Pharmaceutics, Vol. 455, No. 1-2, 2013, p. 57-65.

Research output: Contribution to journalArticle

@article{a087c49f0be44d329bffca487a6a4a5a,
title = "The influence of initial atomized droplet size on residual particle size from pressurized metered dose inhalers",
abstract = "Pressurized metered dose inhalers (pMDIs) are widely used for the treatment of diseases of the lung, including asthma and chronic obstructive pulmonary disease. The mass median aerodynamic diameter of the residual particles (MMADR) delivered from a pMDI plays a key role in determining the amount and location of drug deposition in the lung and thereby the efficacy of the inhaler. The mass median diameter of the initial droplets (MMDI), upon atomization of a formulation, is a significant factor influencing the final particle size. The purpose of this study was to evaluate the extent that MMDI and initial droplet geometric standard deviation (GSD) influence the residual aerodynamic particle size distribution (APSDR) of solution and suspension formulations. From 48 solution pMDI configurations with varying ethanol concentrations, valve sizes and actuator orifice diameters, it was experimentally found that the effective MMDI ranged from 7.8 to 13.3 μm. Subsequently, computational methods were utilized to determine the influence of MMDI on MMADR, by modulating the MMDI for solution and suspension pMDIs. For solution HFA-134a formulations of 0.5{\%} drug in 10{\%} ethanol, varying the MMDI from 7.5 to 13.5 μm increased the MMADR from 1.4 to 2.5 μm. For a suspension formulation with a representative particle size distribution of micronized drug (MMAD = 2.5 μm, GSD = 1.8), the same increase in MMDI resulted in an increase in the MMADR from 2.7 to only 3.3 μm. Hence, the same increase in MMDI resulted in a 79{\%} increase in MMADR for the solution formulation compared to only a 22{\%} increase for the suspension formulation. Similar trends were obtained for a range of drug concentrations and input micronized drug sizes. Thus, APSDR is more sensitive to changes in MMDI for solution formulations than suspension formulations; however, there are situations in which hypothetically small micronized drug in suspension (e.g. 500 nm MMAD) could resemble trends observed for solution formulations. Furthermore, the relationship between APSDR and drug concentration and MMDI is predictable for solution pMDIs, but this is not as straightforward for suspension formulations. In addition, the MMAD R was relatively insensitive to changes in initial droplet GSD (from 1.6 to 2.0) and the solution and suspension pMDI residual particle GSDs were essentially identical to the initial droplet GSDs.",
keywords = "Aerodynamic particle size, Atomized droplets, Initial droplet diameter, Pressurized metered dose inhaler (pMDI), Solution formulation, Suspension formulation",
author = "Poonam Sheth and Stein, {Stephen W.} and Myrdal, {Paul B}",
year = "2013",
doi = "10.1016/j.ijpharm.2013.07.061",
language = "English (US)",
volume = "455",
pages = "57--65",
journal = "International Journal of Pharmaceutics",
issn = "0378-5173",
publisher = "Elsevier",
number = "1-2",

}

TY - JOUR

T1 - The influence of initial atomized droplet size on residual particle size from pressurized metered dose inhalers

AU - Sheth, Poonam

AU - Stein, Stephen W.

AU - Myrdal, Paul B

PY - 2013

Y1 - 2013

N2 - Pressurized metered dose inhalers (pMDIs) are widely used for the treatment of diseases of the lung, including asthma and chronic obstructive pulmonary disease. The mass median aerodynamic diameter of the residual particles (MMADR) delivered from a pMDI plays a key role in determining the amount and location of drug deposition in the lung and thereby the efficacy of the inhaler. The mass median diameter of the initial droplets (MMDI), upon atomization of a formulation, is a significant factor influencing the final particle size. The purpose of this study was to evaluate the extent that MMDI and initial droplet geometric standard deviation (GSD) influence the residual aerodynamic particle size distribution (APSDR) of solution and suspension formulations. From 48 solution pMDI configurations with varying ethanol concentrations, valve sizes and actuator orifice diameters, it was experimentally found that the effective MMDI ranged from 7.8 to 13.3 μm. Subsequently, computational methods were utilized to determine the influence of MMDI on MMADR, by modulating the MMDI for solution and suspension pMDIs. For solution HFA-134a formulations of 0.5% drug in 10% ethanol, varying the MMDI from 7.5 to 13.5 μm increased the MMADR from 1.4 to 2.5 μm. For a suspension formulation with a representative particle size distribution of micronized drug (MMAD = 2.5 μm, GSD = 1.8), the same increase in MMDI resulted in an increase in the MMADR from 2.7 to only 3.3 μm. Hence, the same increase in MMDI resulted in a 79% increase in MMADR for the solution formulation compared to only a 22% increase for the suspension formulation. Similar trends were obtained for a range of drug concentrations and input micronized drug sizes. Thus, APSDR is more sensitive to changes in MMDI for solution formulations than suspension formulations; however, there are situations in which hypothetically small micronized drug in suspension (e.g. 500 nm MMAD) could resemble trends observed for solution formulations. Furthermore, the relationship between APSDR and drug concentration and MMDI is predictable for solution pMDIs, but this is not as straightforward for suspension formulations. In addition, the MMAD R was relatively insensitive to changes in initial droplet GSD (from 1.6 to 2.0) and the solution and suspension pMDI residual particle GSDs were essentially identical to the initial droplet GSDs.

AB - Pressurized metered dose inhalers (pMDIs) are widely used for the treatment of diseases of the lung, including asthma and chronic obstructive pulmonary disease. The mass median aerodynamic diameter of the residual particles (MMADR) delivered from a pMDI plays a key role in determining the amount and location of drug deposition in the lung and thereby the efficacy of the inhaler. The mass median diameter of the initial droplets (MMDI), upon atomization of a formulation, is a significant factor influencing the final particle size. The purpose of this study was to evaluate the extent that MMDI and initial droplet geometric standard deviation (GSD) influence the residual aerodynamic particle size distribution (APSDR) of solution and suspension formulations. From 48 solution pMDI configurations with varying ethanol concentrations, valve sizes and actuator orifice diameters, it was experimentally found that the effective MMDI ranged from 7.8 to 13.3 μm. Subsequently, computational methods were utilized to determine the influence of MMDI on MMADR, by modulating the MMDI for solution and suspension pMDIs. For solution HFA-134a formulations of 0.5% drug in 10% ethanol, varying the MMDI from 7.5 to 13.5 μm increased the MMADR from 1.4 to 2.5 μm. For a suspension formulation with a representative particle size distribution of micronized drug (MMAD = 2.5 μm, GSD = 1.8), the same increase in MMDI resulted in an increase in the MMADR from 2.7 to only 3.3 μm. Hence, the same increase in MMDI resulted in a 79% increase in MMADR for the solution formulation compared to only a 22% increase for the suspension formulation. Similar trends were obtained for a range of drug concentrations and input micronized drug sizes. Thus, APSDR is more sensitive to changes in MMDI for solution formulations than suspension formulations; however, there are situations in which hypothetically small micronized drug in suspension (e.g. 500 nm MMAD) could resemble trends observed for solution formulations. Furthermore, the relationship between APSDR and drug concentration and MMDI is predictable for solution pMDIs, but this is not as straightforward for suspension formulations. In addition, the MMAD R was relatively insensitive to changes in initial droplet GSD (from 1.6 to 2.0) and the solution and suspension pMDI residual particle GSDs were essentially identical to the initial droplet GSDs.

KW - Aerodynamic particle size

KW - Atomized droplets

KW - Initial droplet diameter

KW - Pressurized metered dose inhaler (pMDI)

KW - Solution formulation

KW - Suspension formulation

UR - http://www.scopus.com/inward/record.url?scp=84883877806&partnerID=8YFLogxK

UR - http://www.scopus.com/inward/citedby.url?scp=84883877806&partnerID=8YFLogxK

U2 - 10.1016/j.ijpharm.2013.07.061

DO - 10.1016/j.ijpharm.2013.07.061

M3 - Article

VL - 455

SP - 57

EP - 65

JO - International Journal of Pharmaceutics

JF - International Journal of Pharmaceutics

SN - 0378-5173

IS - 1-2

ER -